Linux og windows på én gang

Nogle windows spil og programmer kan køre under Linux, med Wine: http://www.winehq.com/

http://appdb.winehq.org/

Hvis du vil geninstallere lilo, kører du bare kommandoen "lilo" som root.
Det er som regel lettest at installere Windows først og så Linux, for så finder Linux Windows-installationen og sætter Lilo op automatisk (jeg går ud fra at det også fungerer sådan med Debian, selvom jeg ikke har den store erfaring med netop Debian).

Prøv at kopiere indholdet af din /etc/lilo.conf ind her. Så kan vi sikkert hjælpe dig med at sætte den rigtigt op.

Sorry det lige tog lidt tid.
Nå men her er min lilo conf fil så og windows og linux ligger begge her, men den starter bare linux uden at spørge.

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------      `install-mbr(8)', `/usr/share/doc/lilo/',
#                      and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                        |
# |                                                              |
# | Don't forget to run `lilo' after you make changes to this    |
# | conffile, `/boot/bootmess.txt' (if you have created it), or  |
# | install a new kernel.  The computer will most likely fail to  |
# | boot if a kernel-image post-install script or you don't      |
# | remember to run `lilo'.                                      |
# |                                                              |
# +---------------------------------------------------------------+

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda2

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: text, bmp, and menu
# Look in lilo.conf(5) manpage for details
#
#install=menu

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
#      prompt
#      delay=100
#      timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWTO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# If you used a serial console to install Debian, this option should be
# enabled by default.
# serial=

#
# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
        label=Linux
        read-only
#      restricted
#      alias=1

        initrd=/initrd.img

image=/vmlinuz.old
        label=LinuxOLD
        read-only
        optional
#      restricted
#      alias=2

        initrd=/initrd.img.old


# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#      label=HURD
#      restricted
#      alias=3
other=/dev/hda1
        label=Windows
#      restricted
#      alias=2

Er der ik nogen som kan se hva der er galt og hva der skal stå for at få windows og linux til at køre sammen?

Nå men har fået det til at køre...