cisco kommandoer

Hvilken type er det?

Har du prøvet cisco.com?

Men ellers er der da lidt at hente her:

http://www.paikin.dk/adsl-faq.phtml#19

ALLE....kommandoer

senj...alle typer

Læs lige dette!

Since commands available depend on the ios feature set, version of Cisco IOS, model of router, and so on, there is not a comprehensive list of all commands at levels 1 and 15. For example, show ipx route would be not be present in an ip only feature set, show ip nat trans would not be in Cisco IOS 10.2.X because NAT was not introduced at the time, and show environment would not be present in router models without power supply and temparature monitoring. Commands available in a particular router at a particular level can be found be entering a ? at the prompt in the router when at that privilege level.

Måske her?

http://www.cisco.com/warp/public/752/qrg/

http://www.cisco.com/warp/public/752/qrg/
giver ikke noget, og jeg kan ikke hente PDF-formatet på min student-bruger

Der er ikke eet dokument, der indeholder alle kommandoer for samtlige versioner.
Gå ind på http://www.cisco.com/univercd/home/home.htm og vælg den relevante version under \"Cisco IOS Software\". Vælg derefter \"... Master Indexes\" og derefter \"Cisco IOS Command Reference Master Index\".
Så kan du f.eks. ende på http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122mindx/crfindx.htm

senj....så bare en af typerne. Jeg er \"kun\" nået til 2.semester, så det er kun de mest brugte kommandoer jeg har brug for

Table 1 lists and describes the most commonly used modes, how to enter the modes, and the resulting system prompts. The system prompt helps you identify which mode you are in and, therefore, which commands are available to you.


Table 1: Frequently Used IOS Command Modes  Mode  Description of Use  How to Access  Prompt 
User EXEC
To connect to remote devices, change terminal settings on a temporary basis, perform basic tests, and display system information.
Log in.
Switch>

Privileged EXEC (Enable)
To set operating parameters. The privileged command set includes the commands in user EXEC mode, as well as the configure command. Use this command to access the other command modes.
From the user EXEC mode, enter the enable command and the enable password.
Switch#

Global configuration
To configure features that affect the system as a whole.
From the privileged EXEC mode, enter the configure terminal command.
Switch(config)#

Interface configuration
To enable features for a particular interface. Interface commands enable or modify the operation of a Gigabit Ethernet or Fast Ethernet port.
From global configuration mode, enter the interface type location command.

For example, enter
interface fastethernet 0/0/1
or
interface gigabitethernet 1/0/0.
Switch(config-if)#

Line configuration
To configure the console port or VTY line from the directly connected console or the virtual terminal used with Telnet.
From global configuration mode, enter the line console 0 command to configure the console port, or the line vty line-number command to configure a VTY line.
Switch(config-line)#

arjjj........

hvis i forestiller jer en ordbog der er bygget op i alfabetisk rækkefølge. Og i derefter forestiller jer at disse ord der er i denne \"ordbog\" var kommandoer til cisco-routere (alle(gentager lige: ALLE) de kommandoer der er gældende for routere)

Hvis det så bare var A-L-L-E kommandoer til en model, så betyder det ikke noget.

Har du checket min link af? Den indeholder samtlige routerkommandoer for IOS 12.2.

Vil du have alle detaljer om hver kommando med i dokumentet? Er du klar over, hvor stort det dokument vil blive?

Har du overvejet at finde en Cisco Documentation CD istedet? De følger med alt Cisco udstyr, når man køber det. Jeg er sikker på, at du kan overtale \"nogen\" til at sende dig een, hvis det dækker dit behov.

Kunne ikke bruge svarene til en skid.....men hvad fanden....om ½ år sidder de vel fast i hukommelsen