1) Versionen er 12.0(5)T
2) Jeg tror jeg bruger pap men du kan lige se
hvordan configurationen ser ud.
3)
Cisco801>show dialer
BRI0 - dialer type = ISDN
Rotary group 1, priority = 0
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI0:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
BRI0:2 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
Dialer1 - dialer type = IN-BAND SYNC NO-PARITY
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Number of active calls = 0
Dial String Successes Failures Last DNIS Last status
80900550 0 0 never - Default
Cisco801>
4)
Cisco801>show isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Activated dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
Cisco801>
6) Min konto er aktiveret fordi det er den jeg skriver fra lige nu.
Lige nu har jeg configureret routeren med Cisco ConfigMaker hvilket ser meget nem ud og overskulig men jeg kan stadigvæk ikke få routeren igang. Computeren har nu fået tildelt sin ip 192.168.0.1 og jeg bruger som gateway 192.168.0.2. Når jeg går ind i IE så burde den få routeren til at kalde op men der sker ikke en meter. Muligvis kan du se hvad dette skyldes.
Hele configurationen ser således ud. Jeg har taget passwordene væk :=)
! ******************************************************************
! Cisco801.cfg - Cisco router configuration file
! Automatically created by Cisco ConfigMaker v2.5.1 Build 10
! 16. november 2001, 12:19:20
!
! Hostname: Cisco801
! Model: 801
! ******************************************************************
!
service timestamps debug uptime
service timestamps log uptime
service password-encryption
no service tcp-small-servers
no service udp-small-servers
!
hostname Cisco801
!
enable password mihai
!
ip source-route
no ip name-server
!
isdn switch-type basic-net3
!
ip subnet-zero
no ip domain-lookup
ip routing
!
interface Dialer 1
description connected to Internet
ip address negotiated
ip access-group 101 in
no ip split-horizon
encapsulation ppp
dialer in-band
dialer idle-timeout 120
dialer string 80900550
dialer hold-queue 10
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname ********
ppp chap password ********
ppp pap sent-username ******* password *******
no ppp multilink
no cdp enable
!
interface Ethernet 0
no shutdown
description connected to EthernetLAN
ip address 192.168.0.2 255.255.255.0
ip access-group 100 in
keepalive 10
!
interface BRI 0
no shutdown
description connected to Internet
no ip address
dialer rotary-group 1
!
! Access Control List 100
!
no access-list 100
access-list 100 permit ip any any
!
! Access Control List 101
!
no access-list 101
access-list 101 deny ip 192.168.0.0 0.0.0.255 any
access-list 101 permit tcp any any established
!
! Dialer Control List 1
!
no dialer-list 1
dialer-list 1 protocol ip permit
!
! DHCP Server
!
service dhcp
ip dhcp pool 1
network 192.168.0.0 255.255.255.0
default-router 192.168.0.2
!
router rip
version 2
network 192.168.0.0
passive-interface Dialer 1
no auto-summary
!
!
ip classless
!
! IP Static Routes
ip route 0.0.0.0 0.0.0.0 Dialer 1
no ip http server
no snmp-server location
no snmp-server contact
!
line console 0
exec-timeout 0 0
password mihai
login
!
line vty 0 4
password mihai
login
!
end
Hvis du vil have en ide hvordan diagrammet over netværket i Cisco ConfigMaker ser ud så er den her:
http://users.cybercity.dk/~dko1224/configm.pdfMange Tak fordi du gidder at bruge din tid på at hjælpe mig.
Mvh.
Mihai
