Serverens oppetid.. HVORDAN?!?!

fandte = fandtes ;)

lytter...

Er der ikke nogle kloge hoveder, der ved hvordan denne sag klares!?!? ;)

mener kun det er linux der kan dette =o)

ellers prøv www.tuxtime.dk

den er da bare for cool... :)

space>>> Hvad er Tuxtime.dk for noget!??!

du opretter dig som bruger og installerer en klient på din maskine som så sender oppetidsinfo til tuxtime.dk

du kan se det \"in effect\" her:

http://213.237.80.136

danscape-->  http://www.tuxtime.dk/index.php?page=about

du kan også få sådan en stat ligesom chart.dk bare med uptime

hent uptime.exe fra microsoft på
http://www.microsoft.com/ntserver/nts/downloads/management/uptime/default.asp

så kører du bare uptime.exe med dit asp script og formaterer outputet som du vil have det.. :-)

et eksempel på output er \"\\\\AMD has been up for: 0 day(s), 0 hour(s), 14 minute(s), 53 second(s)\".. sådan ser det ud hvis jeg kører det lige nu.. :-)

delwin>>> Kan du ikke lige definere det mere præcist, hvordan det fungere?!? =) Hvis du har nogle ASP-koder til hvordan man får den til at kører det osv. så må du da meget gerne poste dem!

Jeg har downloadet Uptime i Intel versionen, men der sker ikke noget når jeg kører uptime.exe ?!?


- Kasper =)

Hvordan betjener man programmet!??

der kommer noget frem hvis man skriver C:\\UPTIME.exe /heartbeat  \\\\server03

Men der kan man kune disable og enable den...?!?!

http://support.microsoft.com/default.aspx?scid=kb;EN-US;q232243

Uptime.exe Tool Allows You to Estimate Server Availability with Windows NT 4.0 SP4 or Higher (Q232243)

--------------------------------------------------------------------------------
The information in this article applies to:


Microsoft Windows NT Server version 4.0 SP4
Microsoft Windows NT Server version 4.0 SP4 , , Terminal Server Edition
Microsoft Windows NT Server, Enterprise Edition version 4.0 SP4


--------------------------------------------------------------------------------


SUMMARY
A new tool, Uptime.exe, is available for displaying system availability. Uptime.exe can be used to display the current uptime of the local or remote system. Optionally, it can also scan the Event log for key system events such as system restart or computers that are not responding (hanging). Where possible, it also calculates system availability. It is primarily intended for Windows NT Server 4.0 Service Pack 4 or later, though it operates in limited fashion on earlier versions.



MORE INFORMATION
Uptime.exe is a standalone program. To install the tool, simply copy the file into your Windows NT directory. You may then run the tool at a command prompt.

For extended help on this tool, type the following at a command prompt:


uptime /help
This tool is most accurate when run with administrator privileges, however, even without administrator privileges, the tool attempts to make a best estimate based on available information. In all cases, the results should be considered estimates.

It is important to note that the uptime and availability measurements reflect the local view of the operating system only. The \"Total Uptime\" measurement refers to the sum of all the time during the measured period where the operating system reported itself to be in normal operation. It does not reflect times when the server might be unavailable for other reasons, such at network outages.

It is also important to note that although the operating system is functioning normally, this does not mean that the server programs running on that server are operating normally. For instance, the operating system may be available, but a database running on that server may not be operating correctly.

Uptime depends on the Event log for the data it uses to calculate availability. The tool is not able to make calculations prior to the beginning of the Event log. If the Event log is cleared, no calculations are possible. Certain settings can be disabled limiting the accuracy of this tool. For example, writing an event when the system stops responding and displays a blue screen error message or disabling Dr. Watson for program error messages. Please see the following article in the Microsoft Knowledge Base for information on blue screen error messages:

Q192463 Gathering Blue Screen Information After Memory Dump
Please see the following articles in the Microsoft Knowledge Base for information on Dr. Watson and application errors:

Q188296 How to Disable Dr. Watson for Windows NT
Uptime is only able to calculate availability when using Windows NT 4.0 Service Pack 4 or later. Service Pack 4 introduced a \"heartbeat\" (as described in the Uptime Help file), and additional events for tracking system shutdowns. For more information about these events, please see the following article in the Microsoft Knowledge Base:

Q196452 Why WinNT Reports 6005, 6006, 6008, and 6009 Event Log Entries
This tool is now available at the following Web site:
http://www.microsoft.com/ntserver/nts/downloads/management/uptime/default.asp

Okay Takker =)