Åbne alle porte

Hvad er din udbydder??? Er det worldonline forwarder den automatisk alle porte til dit primære interne IP nummer som er/burde være : 192.168.1.2
Er det ikke Worldonline, så.......tjaaa??*g*

//Henrik

set filter 0 off
set filter 1 off
set filter 2 off
set filter 3 off
set filter 4 off
set filter 5 off
set filter 6 off
set filter 7 off
set filter 8 off
set filter 9 off
set filter 10 off
set filter 11 off
set filter 12 off
set filter 13 off
set filter 14 off
set filter 15 off
set filter 16 off
set filter 17 off
set filter 18 on allow incoming all 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0
set filter 19 on allow outgoing all 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0
write
reboot

så er din Cisco 677 helt åben.

Her er dokumentationen:

http://www.cisco.com/univercd/cc/td/doc/product/dsl_prod/c600s/guidarch/c677inop/04chap03.htm#xtocid1284720

Fungere det på samme måde med en Cisco 760 Series ISDN router???
Spørger af nysgerigheds skyld :)

øøøh tror det - men er ikke sikker

vedr: cisco 760 series port problemer:

en advarsel fra cisco:

Security Scanning software can cause a memory error in Cisco IOS® Software that will cause a reload to occur. This vulnerability affects only Cisco IOS software version 12.1(2)T and 12.1(3)T, and limited deployment releases based on those versions.

Customers using the affected Cisco IOS software releases are urged to upgrade as soon as possible to later versions that are not vulnerable to this defect. Vulnerable products and releases are listed in detail below.

The security scanner makes TCP connection attempts to various ports, looking for open ports to further investigate known vulnerabilities with those services associated with certain ports.  However, a side effect of the tests exposes the defect described in this security advisory, and the router will reload unexpectedly as soon as it receives a request to review or write the configuration file.

This defect is documented as Cisco Bug ID  CSCds07326.

An attempt to make a TCP connection to ports 3100-3999, 5100-5999, 7100-7999, and 10100-10999 will cause the router to unexpectedly reload at the next show running-config, or write memory, or any command that causes the configuration file to be accessed. Cisco IOS software cannot be configured to support any services that might listen at those port addresses, and cannot be configured to accept connections on those ports, however, connection attempts to these ports in the affected version will cause memory corruption, later leading to an unexpected reload.

Software packages are available from various commercial and free sites that perform automated remote tests for computer security vulnerabilities by scanning computers on a network for known security flaws.  A common log message in environments that experienced security scan related crashes was the "attempt to connect to RSHELL" error message.

Bug ID
This problem was introduced in 12.1(1.3)T, and is identified by Cisco Bug ID CSCds07326.

oxygenic: 7xx kører IOS700 (som IKKE er det samme som IOS), 6xx kører CBOS.
Så nej, du kan ikke bruge alle de spørgsmål/svar om 6xx her på eksperten til noget, hvis du har en 7xx.

Det er ikke mig der har en Cisco760, var bare nysgerrig, da en af mine venner har en Cisco 760 router (ISDN router).
Men jeg har et andet spørgsmål som I måske kan besvare...
hvordan sætter man IIS 4.0 (Microsoft Personal Webserver) op så den også virker når man er bag en router???
Normalt når man kører med IIS skriver man fx: http://212.242.68.9/  (WAN-IP)
men det virker ikke når man sidder bag en router, hvorfor det, og hvordan løser man det problem?
jeg har fået avide at IIS 4.0 skal knyttes til en port (fx. port 80), men hvordan gør jeg det?