Avatar billede dennism Nybegynder
16. februar 2002 - 23:53 Der er 21 kommentarer og
1 løsning

Driver (HP PSC 500´)

Jeg har idag fået en 'HP PSC 500' printer/scanner/kopi... Men driveren virker ikke til WinXP...

Hvor kan jeg finde en som virker til Windows XP?
Avatar billede dennism Nybegynder
16. februar 2002 - 23:55 #1
Har kigget på www.hp.com... Men uden held :-(
Avatar billede rkhdk Nybegynder
16. februar 2002 - 23:57 #2
Avatar billede rkhdk Nybegynder
16. februar 2002 - 23:57 #3
printable version

HP All-in-One Products - HP Officejet Pro, R, and PSC 500 Series Products: Microsoft (R) Windows XP Information



In this document:
Document summary

Introduction

Before upgrading to Windows XP

Installing the drivers built into Windows XP

Features supported with the Windows XP drivers

Using the print and scan drivers

If the print or scan mini-drivers do not load or plug and play does not occur

Third-party software

More information for your product




Return to the HP Officejet, PSC and Copyjet products Microsoft Windows XP page.

Document summary
The following is a summary of the contents of this document. More detailed information is available on all these topics within this document.

This document covers Windows XP compatibility for the HP Officejet Pro 1150 and 1170 series, HP Officejet R series, and the PSC 500 series all-in-one products.
Before connecting the all-in-one to the computer or before upgrading to Windows XP, there are settings to check or change as well as other actions that should be taken.
All of the printing and scanning drivers required for the products covered in this document are built into Windows XP. These drivers are installed by Windows plug and play.
The drivers built into Windows XP provide most if not all of the previous functionality of the all-in-one when combined with other Windows XP features.
HP will not be releasing any additional Windows XP drivers for these products.
No third party software (such as OCR) or manager software are included with the drivers built into Windows XP.
HP document bpu01863 - Scanning and Printing Photos in Windows XP with a Directly Connected HP All-in-one Product contains information about using the built-in drivers to print and scan images in Windows XP.
HP document bpu01862 - Solving Microsoft (R) Windows XP Install Issues While Installing HP All-in-One Product Mini-Drivers contains information on resolving driver installation issues.
Introduction
The products listed in this document can be used with Windows XP immediately using drivers built into Windows XP. HP worked with Microsoft to include built-in print and scan drivers with the Windows XP operating system. Because these drivers are included with Windows XP, no downloads or additional software are required. Simply connect your product to your PC, and Windows XP will automatically install the necessary drivers.

NOTE: Do not attempt to install the software from the CD-ROM that came with your HP all-in-one product. It was not designed to work with Windows XP.

These drivers, when combined with the front panel features and those features built into Windows XP, provide much of the same functionality that the product had in other Windows operating systems.

This document addresses the Windows XP operating system and all product models of the following HP all-in-one product families:

HP Officejet Pro series (1150C, 1150xi, 1170C, 1170Cse, 1170Cxi, 1175Cse and 1175Cxi)
HP Officejet R series (R40, R40xi, R60, R45, R60, R65, R80, and R80xi)
HP PSC 500 series (PSC 500 and PSC 500xi)
NOTE: Owners of computers that did not originally have Windows XP installed should also contact their computer manufacturer to determine if system updates are required to run Windows XP.

Before upgrading to Windows XP
Before upgrading your version of Windows to Windows XP, the following steps must be performed. If the software is not uninstalled prior to upgrading the operating system, it may be difficult to get the product to install correctly in Windows XP. Try uninstalling the software from Windows XP if this occurs.

Uninstall the HP all-in-one software.
For Windows 95, 98, Me, and NT 4.0, do the following:

Click Start, Settings and then Control Panel.
Double-click Add/Remove Software.
Locate and highlight the HP all-in-one product software from the list of installed programs.
Click Add/Remove and then follow the prompts that appear.
For Windows 2000, do the following:

Click Start, Settings and then Control Panel.
Double-click Add/Remove Software.
Locate and highlight the HP all-in-one 2000 software (if present) from the list of installed programs.
Click Add/Remove and then follow the prompts that appear.
Right-click My Computer and select Properties.
Select the Hardware tab and click Device Manager.
Expand the DOT4 entry and highlight the HP product below as indicated below in Figure 1.
Click Actions and then Uninstall.
Figure 1: Locating the all-in-one product entry under Dot4 in the Device Manager



After the uninstall is complete, disconnect the communications cable to the HP all-in-one from the computer.
Restart the computer and then upgrade to Windows XP.
Verify that in the computer's BIOS, the parallel port mode is set to ECP. View HP document bpu08011 - Setting the Parallel Port Mode to ECP and its Benefits or contact the computer manufacturer for assistance with this task. The all-in-one may fail to install or have communications problem if the parallel port is not in ECP mode.
Check and set the port settings in Device manager. This is very important. The all-in-one may not be detected if this step is not done.
Click Start, right click My Computer, and select Properties. This will bring up the System Properties screen.
Select the Hardware tab and then click Device Manager.
Locate the Ports section and click the plus (+) beside it to open the list of available ports.
Double-click the parallel port entry that the all-in-one is connected to. This will normally be LPT 1. The parallel port properties screen should open.
Select the Port Settings tab.
Select the option to Use any interrupt assigned to the port and place a check in Enable legacy plug and play detection. Click OK to accept the changes.
Close the Device Manager and then click OK to close the System Properties. It may be necessary to reboot the computer before the changes will take affect.
Installing the drivers built into Windows XP
Do not attempt to install software from the CD-ROM that came with the product. These drivers will not work in Windows XP. Follow these instructions to install the print and scan drivers after upgrading to Windows XP:

Turn the computer off.
Connect the parallel communications cable to the all-in-one product and the computer.
Apply power to the all-in-one and verify that it is on.
Start the computer. During the start-up process, Windows XP will detect the HP all-in-one and begin installing drivers.
If an Add New Hardware screen appears, click Next and then select the correct product model
Avatar billede nordicwolf Nybegynder
17. februar 2002 - 00:02 #4
hvad så med www.hp-hjemme.dk
Avatar billede retaxes Nybegynder
17. februar 2002 - 00:06 #5
man skal ikke bruge den CD der følger med, så går det hele i kage!
Avatar billede NanoQ Nybegynder
17. februar 2002 - 00:07 #6
Du SKAL bruge Windows XP's indbyggede driver. Den fungerer helt fint.

jeg har selv en PCS 500. Den har voldt mig store problemer. Mine problemer var dog, at min Windows XP var opgraderet fra Windows ME, uden først at afinstallere de gamle drivere. Jeg har haft oprettet flere spørgsmål her på Eksperten vedr. dette. Efter en snak med HP, fandt jeg frem til at eneste løsning var reinstallation af XP.

Herefter har alt kørt fint. Du kan dog ikke benytte de medfølgende programmer til printeren.

Jeg bruger Corel Photopaint's scan funktion (almindelig TWAIN). Det kører faktisk bedre end HP's eget scannersoftware.

/NanoQ
Avatar billede retaxes Nybegynder
17. februar 2002 - 00:09 #7
rkhdk> det var da ikke nødvendig med den lange smøre ;o)

HP vedlægger store advarsler i de nye printere, herunder G55, om at man IKKE må bruge den medfølgende Cd i WinXP!!
Avatar billede rkhdk Nybegynder
17. februar 2002 - 00:10 #8
retaxes => jeg makerede også kun
NOTE: Do not attempt to install the software from the CD-ROM that came with your HP all-in-one product. It was not designed to work with Windows XP.

men alligevel kom ALT med!
Avatar billede dennism Nybegynder
17. februar 2002 - 00:11 #9
Hvor kan jeg hente:
Corel Photopaint's scan
Avatar billede retaxes Nybegynder
17. februar 2002 - 00:12 #10
nanoq> velkommen tilbage under dit gamle navn.

Jeg kan godt huske dit spm. vedr. PCS 500, så da jeg fik en G55 skulle jeg ikke nyde noget, men fulgte anvisningerne fra HP!
Avatar billede retaxes Nybegynder
17. februar 2002 - 00:13 #11
rkhdk> ok, det kan jo glippe ind imellem ;o)
Avatar billede NanoQ Nybegynder
17. februar 2002 - 00:17 #12
dennism, det kan du ikke... det er en del af Corel Draw pakken.

Men du kan scanne med de fleste grafikprogrammer... det kræver kun de har TWAIN understøttelse.

retaxes, takker :)
Avatar billede retaxes Nybegynder
17. februar 2002 - 00:25 #13
dennism> du kan starte scanning inde fra Kontrolpanel under Scannere og kamera.

Og ellers startes scanning i alle programmer der benytter sig af Twaindriveren. Photoshop, Caere Omnipage-OCR for blot at nævne nogle af dem.
Avatar billede dennism Nybegynder
17. februar 2002 - 08:33 #14
Når jeg gør ind under Scannere og kameraer, er der ikke noget scanner...
Og hvis jeg vil tilføje kan jeg kun tilføje HP`s kamerare, og ikke nogle scannere!
Jeg har prøvat at søge efter hardware, under tilføj hardware, men der sker ikke noget! Og ja, den er tilsluttet korrekt! Jeg kan nemlig godt printe!
Hvad skal jeg gøre for at installere scanneren korrekt?
Avatar billede dennism Nybegynder
17. februar 2002 - 08:33 #15
Den kom nu...
Avatar billede dennism Nybegynder
17. februar 2002 - 08:50 #16
Kan man scanne via netværk?
altså, kan jeg installere en scanner på 192.168.0.2, og scanner på 192.168.0.1?
Avatar billede rkhdk Nybegynder
17. februar 2002 - 10:52 #17
det kræver at du har en speciel Netværks scanner..
du kan ikke dele en scanner, ligesom med en printer!!
Avatar billede dennism Nybegynder
17. februar 2002 - 11:17 #18
Og min HP 500, er altså ikke en netværks scanner?
Avatar billede rkhdk Nybegynder
17. februar 2002 - 11:33 #19
jeg ved det ikke :-(
men jeg tror det ikke
Avatar billede retaxes Nybegynder
17. februar 2002 - 11:42 #20
på en G55 kan man godt bruge den som netværksscanner, men det er en feature man skal købe ved siden af.

Når du ikke kunne finde scanneren i kontrolpanelet, så er det fordi den er slukket!
Avatar billede retaxes Nybegynder
17. februar 2002 - 11:45 #21
se i din manual om scanneren kan bruges på netværket.
Avatar billede NanoQ Nybegynder
17. februar 2002 - 13:24 #22
pcs500 er ikke ne netværksscanner. Og du kan ikke få netværksoptions til den :)
Avatar billede Ny bruger Nybegynder

Din løsning...

Tilladte BB-code-tags: [b]fed[/b] [i]kursiv[/i] [u]understreget[/u] Web- og emailadresser omdannes automatisk til links. Der sættes "nofollow" på alle links.

Loading billede Opret Preview
Kategori
IT-kurser om Microsoft 365, sikkerhed, personlig vækst, udvikling, digital markedsføring, grafisk design, SAP og forretningsanalyse.

Log ind eller opret profil

Hov!

For at kunne deltage på Computerworld Eksperten skal du være logget ind.

Det er heldigvis nemt at oprette en bruger: Det tager to minutter og du kan vælge at bruge enten e-mail, Facebook eller Google som login.

Du kan også logge ind via nedenstående tjenester