pc-card adapter

Hvad sker der når du slukker og tænder igen

Har du undersøgt om der findes en driver til kameraet på producentens hjemmeside. Selvom Windows NT ikke understøtter USB er det ikke ensbetydende med, at dit kamera ikke virker på systemet. Flere og flere producenter har lavet specielle drivere som godt kan køre på en Windows NT-maskine...

PS. Hvorfor spørger du ikke firmaet om ikke de kan skifte Windows NT til Windows 2000? Det er jo ikke særlig optimalt, at det ikke virker, når du skal bruge kameraet for udføre dit arbejde...

Der findes ikke en Canon Ixus v2 driver til NT. EDB-afdelingen i mit firma har sagt at maskinen (nogle af programmerne måske) ikke kan køre 2000, og nu skal jeg til Australien mandag morgen. Jeg skal bruge mine programmer, men skal også gerne kunne sende billeder hjem. Hvorfor virker den der adapter ikke? Er det måske fordi der sidder et modem i sokkel1?

Det kan godt ske at adapeteren skal sidde i sokkel1. Prøv at fjerne modemet helt og kun installere adapteren. Hvad er det for en SmartCard-adapter du har købt?

Adapteren hedder Sandisk pc-card adapter og læser compact flash (ikke smartcard som jeg kom til at skrive)Den er købt hos Nem-direct

Prøv det her

<rip>
SanDisk Card Reader
PC Card Adapter
The PC Card Adapter must be configured using the following instructions:

Login with an Administrative Account.
Click START -- PROGRAMS -- Administrative Tools -- Windows NT Diagnostics.
Click Resources tab. Check to see that IRQ 3 is not listed. If it is, then check to see if IRQ 5 or IRQ 9 is not listed. You need to use the first available IRQ of the above listed. If none of the above IRQ's are not available, then you should not use the PC card adapter.
You must have the camera software already installed for this card reader to function properly.
Insure that you have 3 profiles configured on your system. Docked, Undocked (Network Support), Undocked (No Network Support). If these are not configured on your laptop contact your IT Specialist.
Check the hardware profiles for the network cards:  (Contact your IT specialist if you have any questions.)
    1. Click Settings.
    2. Click Control Panel.
    3. Double-click Devices icon.
    4. Click 3Com 3C920 Adapter Driver to highlight.
    5. Click HW Profiles button.
    6. The device should be enabled in the docked state and disabled in the other two. Change as needed
        and Click OK.
    7. Click 3Com Megahertz 10/100 LAN CardBus to highlight.
    8. Click HW Profiles button.
    9. The device should be enabled in the Undocked (Network Support) state and disabled in the other
        two. Change as needed and Click OK.
    10. Click Close and close out the Control Panel window.
Click Start -- Shutdown.
Select Close all programs and log on as a different user.
Login with an Administrator account.
Click Start -- Settings -- Control Panel
Double-click SCSI Adapters.
Click Drivers tab. If you only see one card installed skip to the next step. (Should be a PCI IDE card) If you see the PCMCIA IDE card installed, then highlight it and click Remove. After the card is removed shutdown and restart the workstation. Once the system is back up continue under an Administrator account.
Right-Click on the PC Card in the Task bar and stop the modem card (3Com Megahertz 3CXM356). Remove the modem card from the top slot, you may see a dialog box saying the card has been removed. Click OK  and insert the card reader and camera card into the slot.
Allow the system to recognize the card as a new piece of hardware. Select to install the card with the software (recommended). It should recognize it as a SunDP card type. Click OK.
When it comes to the configuration screen, then next to the IRQ level, click on the down arrow tab and select IRQ 3.
Keep the selection for I/O port as Auto.
Click OK.
Reboot your workstation.
NOTE: Always Right-click on the PC Card in the Task bar and stop the card you are removing before removing the card from the PCMCIA slot. The top slot contains the modem and would be card 3Com Megahertz 3CXM356 and the Card reader is the SDP card.

NOTE:  If you have any problems or questions during these instructions please contact your IT Specialist.
</rip>

Hej somaliomar, du har gjort et stort arbejde for at hjælpe mig, så du får mine point, selv om det ikke umiddelbart har været din løsning der hjalp. Jeg kan faktisk godt læse billederne på compact flash kortet nu, men det er blevet til c: drev og c: drevet til d: - det har jeg så accepteret, for computeren starter godt nok op, og når jeg fjerner kortet er alt som før.
hilsen peter-rasmussen@mail.dk

OK. Tak for points :)