Cisco 803 password !

Jeg mener at du resetter den ved at tage strømmen fra i et stykke tid, og så er der en lille tingest du tager ud og i igen. Men det står i manualen til din router.

Er taget fra deres hjemmeside:

Recovering a Lost Enable Password
This section describes how to recover a password that you configured with the enable command (enable password).


--------------------------------------------------------------------------------
Note  You can recover a lost enable password but not a password that you configured with the enable secret command (enable secret password). This password is encrypted and must be replaced with a new enable secret password. See the \"Hot Tips\" section on Cisco Connection Online (CCO) for information on replacing enable secret passwords.

--------------------------------------------------------------------------------

Follow these steps to recover a lost enable password:


--------------------------------------------------------------------------------
Step 1  Connect an ASCII terminal or a PC running a terminal emulation program to the Console port. For more information, see the Cisco 800 Series Routers Hardware Installation Guide.

Step 2  Configure the terminal at 9600 baud, 8 data bits, no parity, and 1 stop bit.

Step 3  Reboot the router.

Step 4  From the user EXEC mode, display the existing configuration register value:

Router> show version



Step 5  Record the setting of the configuration register.

The setting is usually 0x2102 or 0x102.

Step 6  Record the break setting.


Break enabled—bit 8 is set to 0.


Break disabled (default setting)—bit 8 is set to 1.


--------------------------------------------------------------------------------
Note  To enable break, enter the config-register 0x01 global configuration command.

--------------------------------------------------------------------------------

Step 7  Do one of the following:


If break is enabled, go to Step 8.


If break is disabled, turn the router off, wait 5 seconds, and turn it on again. Before the terminal displays Boot..., press Escape or Control-C. The terminal displays the ROM monitor prompt (boot#).
Go to Step 9.


--------------------------------------------------------------------------------
Note  Some terminal keyboards have a key labeled Break. If your keyboard does not have a Break key, refer to the documentation that came with the terminal for instructions on how to send a break. 

--------------------------------------------------------------------------------

Step 8  Send a break. The terminal displays the following prompt:

boot#


Step 9  Reset the configuration register:

boot# set ios-conf = 142



Step 10  Initialize the router:

boot# boot [flash]


The router cycles its power, and the configuration register is set to 0x142. The router uses the boot ROM system image, indicated by the system configuration dialog:

--- System Configuration Dialog ---


Step 11  Enter no in response to the prompts until the following message is displayed:

Press RETURN to get started!


Step 12  Press Return. The following prompt appears:

router>


Step 13  Enter privileged EXEC mode:

router> enable



The prompt changes to the privileged EXEC prompt:

router#


Step 14  Display the enable password in the configuration file:

router# show startup-config



Step 15  Enter configuration mode:

router# configure terminal



Step 16  Reset the configuration register:

router# config-register value



Specify the value that you recorded in Step 5 (usually 0x2102 or 0x102).

Step 17  Press Ctrl-Z to exit configuration mode.


--------------------------------------------------------------------------------
Note  To return to the configuration being used before recovering the lost enable password, do not save the configuration changes before rebooting the router.

--------------------------------------------------------------------------------

Step 18  Reboot the router and enter the recovered password.


--------------------------------------------------------------------------------

ved ike om det kan bruges..

ovenstående metode er til at få sit password tilbage. Besværligt med det virker. Det ville nog være lettere at bare resette den.

Prøv at se om der en slags lille jumper du kan tage ud og ind igen.

Forslag:
Når den er startet op så prøv bare og tryk enter,
prøv og skriv noget basalt som net

Hvis dette ikke virker så er jeg ret sikker på at metoden på dette link virker, 100% sikker.

http://www.cisco.com/warp/public/474/pswdrec_800.html

Nej nu ved jeg hvad du skal!!!!!!!!!!!!!

1: Åbn Internet Explorer.
2: Skriv 192.168.1.1 i adressebaren (tryk enter)
3: Du skulle nu gerne komme ind på en side hvor du kan programmere alt muligt med Routeren og se status....
4: I venstre frame er der noget der heder \"Reset Router\"

zycho> det vil ikke virke når han ikke kender kodeordet ;)