EdiMax 6200n / huawei E1750 / CallMe

Hvad så med 3G-6200n / E1750 / Telia?
Nogen der har fået det til at køre?
Så er jeg meget interesseret i at høre om indstillingerne i Edimax'en.
CallMe kommer jo via Telias mobilnet.

(EdiMax 3G-6200n er flashed med firmware v2.15)

Eller, er der nogen der har succes med
en hvilkensomhelst router / CallMe (apn: websp) / E1750 ?

Så er jeg desperat nok til at købe anden router.
Jeg vil meget gerne undgå at skulle "skrælle" en gammel laptop eller lignende, kun for at få WIFI fra Huawei E1750 / CallMe
(Men OK, ingen hjælp betyder så at jeg er tre skridt nærmere den musikserver jeg aldrig har fixet mig)
Bange for at det er løsningen :-(

Jeg deler gerne fler points ud, hvis det er det der driver værket.
Ved bare ikke hvor knappen sidder, man skruer op for pointe med.
Den gir jeg osse gerne points for hjælp med at finde, fniiis
;-)

Jeg er en ny N00b her.
Ka lisågodt indrømme...
Ingen respons - gør jeg noget forkert her i forum?

Nu får I at se hvad min EdiMax 3G-6200n siger:

Jun 26 14:17:54 (none) syslog.info syslogd started: BusyBox v1.11.1
Jun 26 14:17:59 (none) local2.notice pppd[12943]: pppd 2.4.4 started by root, uid 0
Jun 26 14:18:00 (none) local2.info chat[12946]: abort on (BUSY)
Jun 26 14:18:00 (none) local2.info chat[12946]: abort on (NO CARRIER)
Jun 26 14:18:00 (none) local2.info chat[12946]: abort on (ERROR)
Jun 26 14:18:00 (none) local2.info chat[12946]: abort on (NO DIAL TONE)
Jun 26 14:18:00 (none) local2.info chat[12946]: abort on (NO ANSWER)
Jun 26 14:18:00 (none) local2.info chat[12946]: abort on (DELAYED)
Jun 26 14:18:00 (none) local2.info chat[12946]: report (CONNECT)
Jun 26 14:18:00 (none) local2.info chat[12946]: timeout set to 10 seconds
Jun 26 14:18:00 (none) local2.info chat[12946]: send (AT^M)
Jun 26 14:18:00 (none) local2.info chat[12946]: expect (OK)
Jun 26 14:18:00 (none) local2.info chat[12946]: AT^M^M
Jun 26 14:18:00 (none) local2.info chat[12946]: OK
Jun 26 14:18:00 (none) local2.info chat[12946]:  -- got it
Jun 26 14:18:00 (none) local2.info chat[12946]: send (ATZ^M)
Jun 26 14:18:00 (none) local2.info chat[12946]: expect (OK)
Jun 26 14:18:00 (none) local2.info chat[12946]: ^M
Jun 26 14:18:00 (none) local2.info chat[12946]: ATZ^M^M
Jun 26 14:18:00 (none) local2.info chat[12946]: OK
Jun 26 14:18:00 (none) local2.info chat[12946]:  -- got it
Jun 26 14:18:00 (none) local2.info chat[12946]: send (ATE0V1&F&D2&C1S0=0S7=60^M)
Jun 26 14:18:00 (none) local2.info chat[12946]: timeout set to 30 seconds
Jun 26 14:18:00 (none) local2.info chat[12946]: expect (OK)
Jun 26 14:18:00 (none) local2.info chat[12946]: ^M
Jun 26 14:18:00 (none) local2.info chat[12946]: ATE0V1&F&D2&C1S0=0S7=60^M^M
Jun 26 14:18:00 (none) local2.info chat[12946]: OK
Jun 26 14:18:00 (none) local2.info chat[12946]:  -- got it
Jun 26 14:18:00 (none) local2.info chat[12946]: send (ATDT*99#^M)
Jun 26 14:18:00 (none) local2.info chat[12946]: expect (CONNECT)
Jun 26 14:18:00 (none) local2.info chat[12946]: ^M
Jun 26 14:18:00 (none) local2.info chat[12946]: ^M
Jun 26 14:18:00 (none) local2.info chat[12946]: CONNECT
Jun 26 14:18:00 (none) local2.info chat[12946]:  -- got it
Jun 26 14:18:00 (none) local2.info chat[12946]: send (^M)
Jun 26 14:18:00 (none) local2.info pppd[12943]: Serial connection established.
Jun 26 14:18:00 (none) local2.debug pppd[12943]: using channel 3
Jun 26 14:18:00 (none) local2.info pppd[12943]: Using interface ppp4
Jun 26 14:18:00 (none) local2.notice pppd[12943]: Connect: ppp4 <--> /dev/ttyUSB0
Jun 26 14:18:03 (none) local2.debug pppd[12943]: sent [LCP ConfReq id=0x1 <mru 1412> <asyncmap 0x0> <magic 0x8cff5d4e> <pcomp> <accomp>]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: rcvd [LCP ConfReq id=0x0 <asyncmap 0x0> <auth chap MD5> <magic 0xf3b106> <pcomp> <accomp>]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: No auth is possible
Jun 26 14:18:03 (none) local2.debug pppd[12943]: lcp_reqci: returning CONFREJ.
Jun 26 14:18:03 (none) local2.debug pppd[12943]: sent [LCP ConfRej id=0x0 <auth chap MD5>]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: rcvd [LCP ConfAck id=0x1 <mru 1412> <asyncmap 0x0> <magic 0x8cff5d4e> <pcomp> <accomp>]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xf3b106> <pcomp> <accomp>]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: lcp_reqci: returning CONFACK.
Jun 26 14:18:03 (none) local2.debug pppd[12943]: sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0xf3b106> <pcomp> <accomp>]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: sent [CCP ConfReq id=0x1 <bsd v1 15>]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: rcvd [LCP DiscReq id=0x2 magic=0xf3b106]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: rcvd [LCP ProtRej id=0x3 80 fd 01 01 00 07 15 03 2f]
Jun 26 14:18:03 (none) local2.debug pppd[12943]: Protocol-Reject for 'Compression Control Protocol' (0x80fd) received
Jun 26 14:18:04 (none) local2.debug pppd[12943]: rcvd [IPCP ConfNak id=0x1 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
Jun 26 14:18:04 (none) local2.debug pppd[12943]: sent [IPCP ConfReq id=0x2 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: rcvd [IPCP ConfReq id=0x0]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: ipcp: returning Configure-NAK
Jun 26 14:18:05 (none) local2.debug pppd[12943]: sent [IPCP ConfNak id=0x0 <addr 0.0.0.0>]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: rcvd [IPCP ConfRej id=0x2 <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: sent [IPCP ConfReq id=0x3 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14>]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: rcvd [IPCP ConfReq id=0x1]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: ipcp: returning Configure-ACK
Jun 26 14:18:05 (none) local2.debug pppd[12943]: sent [IPCP ConfAck id=0x1]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: rcvd [IPCP ConfNak id=0x3 <addr 10.233.163.64> <ms-dns1 62.44.166.197> <ms-dns2 62.44.166.69>]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: sent [IPCP ConfReq id=0x4 <addr 10.233.163.64> <ms-dns1 62.44.166.197> <ms-dns2 62.44.166.69>]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: rcvd [IPCP ConfAck id=0x4 <addr 10.233.163.64> <ms-dns1 62.44.166.197> <ms-dns2 62.44.166.69>]
Jun 26 14:18:05 (none) local2.debug pppd[12943]: ipcp: up
Jun 26 14:18:05 (none) local2.warn pppd[12943]: Could not determine remote IP address: defaulting to 10.64.64.68
Jun 26 14:18:05 (none) local2.notice pppd[12943]: local  IP address 10.233.163.64
Jun 26 14:18:05 (none) local2.notice pppd[12943]: remote IP address 10.64.64.68
Jun 26 14:18:05 (none) local2.notice pppd[12943]: primary  DNS address 62.44.166.197
Jun 26 14:18:05 (none) local2.notice pppd[12943]: secondary DNS address 62.44.166.69
Jun 26 14:18:05 (none) local2.debug pppd[12943]: Script /etc/ppp/ip-up started (pid 12953)
Jun 26 14:18:10 (none) local2.debug pppd[12943]: Script /etc/ppp/ip-up finished (pid 12953), status = 0x0


  *  *  *


"Jun 26 14:18:03 (none) local2.debug pppd[12943]: No auth is possible"
Er helt fint med mig. Jeg har sat PIN code på dongle til "disable".

Det meste er sort wobbeligob snak for mig, men
"Could not determine remote IP address: defaulting to 10.64.64.68" bryder jeg mig ikke om.

Jeg spekulerer på om CallMe holder igen hvis de kan lugte NAT hos bruger (= router).
Altså 1 x kort / dongle pr PC.
Jeg har ikke læst om den begrænsning noget sted.
Bare en tanke.

Talk to Me guys.

Dem med Edimax 3G-6200n og Telia eller CallMe
- HVIS DE FINDES!

En stor hjælp ville sføli være den backup-fil man kan lave med routeren under:
Home / Tools / Configuration setup / backup...