Hvad menes der her?

!!! Always must be using BRAIN !!!  :D :D  Meget morsom hjælpeside...jeg kan desværre ikke hjælpe dig.

Tror han sprechen Newb?

Så vidt jeg kan se mener han at
H4 H3 H2 H1 L4 L3 L2 L1 = 1 byte hvor Hx er den høje og Lx er den lave - det vil sige to firecifrede numre sat sammen til een 8-cifret byte.
f.eks HEX 1A er det samme som 00011010 og det han så skriver er "set H4 to 1". Det vil sige din byte skal se således ud: 10011010  som er det samme som 9A hex.

Håber det giver lidt mening :o)
HenningA

Nå ja.. Det er garenteret det han mener! VIl lige prøve det i morgen. Men det er altså heller ikke nemt når han er SÅ dårlig til at forklare sig.

DOHH! Nu ser det ud til at hans side er offline! Er det noget med at google gemmer siderne cached og hvordan bruger man det? eller er der nogen som stadig har siden til at ligge på sin computer som lige vil sende den til mig?

ALL is on Your own risk. ALL is on Your own risk. ALL is on Your own risk. ALL is on Your own risk

!!! Always must be using BRAIN !!! H4 H3 H2 H1 L4 L3 L2 L1 is b7 b6 b5 b4 b3 b2 b1 b0.

Note: first must be enabled writing to memory: Page: 0 Address: 1 Data: set from 0 to 1. Store -it not have to be.

NEW: Emergency button on DVin_lite v1.7 and new changes in CHECKSUMs . See below.

Here is some useful codes for better work with new Sony D8 camcorders, f.eg. TRV120E (TRV125E ... TR8000 ...). All using codes is on your own risk. .

All changes make on PAGE D:

Show Clone(Apperture)/Gain

1A
set H4 to 1
- in manual Exposure is displayed Clone(Apperture) and Gain

ZEBRA effect

1B
set H2 to 1
- useful for manual Exposure. Zebra stripe warning, where is much light.

- menu LCD SET

WHITE BALANC

23
set L2 to 1
- works after restart. New menu MANUAL SET - WHT BAL

- AUTO, HOLD, OUTDOOR, INDOOR. HOLD memorizes last value from AUTO (you must waiting some time, when analyzing of white ending ).

INTERVAL Recording

16
set H1 to 1
- in menu CAMERA SET ( press Start/Stop = 12-13 recorded frames in PAL )

FRAME Recording

16
set L4 to 1
- in menu CAMERA SET , options INTERVAL , REC TIME

COLOUR Bar

1E
set L1 to 1
- is possible record to tape calibration color bars . in menu OTHERS

set H4 to 1

Player / VTR mode ( recording enabling )

14
set L2 to 1
- enabling recording , switch camcorder to VTR mode in "PLAYER"

DV-in / firewire input / enable - camcorder must be ser in VTR mode ( address 14 L2 to 1 ) - it is usefull to convert Analog to DV in time. Don't forget - use true cable SCART-CINCH and no SCART<-CINCH boundled with camcorder !)>

2C
set L1 to 1
When L1 = 0, only Analog inputs work ( it is useful too )

ESP/ELP mode enable - Extra long playtime for cassetes - on some camcorder has no effect.

2C
set L3 to 1
- enabling ESP/ELP mode

A/V DVout mode enable - A/D converter in Player mode. It is INDEPENDENT on status of VTR or DV-in.

2C
set H3 to 1
- enabling A/V DVout in Player mode - NEW

MIC level - enable manual control of audio signal level for microphones - on some camcorder has no effect.

23
set L3 to 1
- enabling MIC audio level

GAIN SHIFT - enable new menu in CAMERA mode for switching of Gain to 0dB or -3dB.

1E
set L2 to 1
- enabling Gain Shift menu



Memory of camcorder has checksum. Checksum is checked always, when was unpluged power sources. When is found bad checksum, camcorder is blocked ( not damaged, is possible repair it ):

- must be set old data. But camcorder turn off after cca 5-10s and LANC not works. Next sentence aren't validate yet: "You must continualy OPEN/CLOSE door of cassete and in this time works with memory".

I have new function on my DVin_lite ! It is "Emergency" button. When is your camcorder blocked, you can easy switch camcorder to emergency mode and then you can easy repaired data.. How ? You connect the blocked camcorder (AC/DC and main batery are removed, camcorder is turn off ) to PC and run DVin_lite v. 1.7. When you get message: "Check cable ...", press "YES". Insert power source (main batery or AC/DC) and then press "Emergency" button and wait cca 20s to next message and your camcorder is working

New metod for checksums:
1) enable changes in memory: 00:01:00 to 00:01:01 (Store)
2) change data on page D, how You need (all with STORE).
3) read new value:
"xx" from 02:F0
"yy" from 02:F1
4) enable update and visibility of checksums on (0F:FE and 0F:FF):
00:FF:00 -> 00:FF:02 (STORE)
00:01:01 -> 00:01:80 (STORE)
5) update new checksums:
write to address:
0F:FF data "xx" ( from 02:F0 ) (STORE)
0F:FE data "yy" ( from 02:F1 ) (STORE)
6) disable changes:
00:FF:02 -> 00:FF:00 (STORE)
00:01:80 -> 00:01:00 (STORE)







NEW: Easy way to convert Analogue signal to Digital with options A/V-DVout in Player mode.

Download of lite program for change memory: DVin_Lite . Adapter is same as for ANIN.EXE.


 


DVinD8SE.ZIP - program for temporary VTR/DVin mode for TRV8000, TRV120E, TRV320E ...

- For memory dump you can use rm95 freeware in DOS prompt or DOS: RM95DUMP.EXE memory.txt .

Very thanks all men, which had courage to test codes, which I found from dump of their camcorder.



ALT DER STÅR PÅ SIDEN LOL...

Yehaa! Det' fedt!
Så er der nok nogen som har fået flere funktioner i sit videokamera.
Hvis der er nogen som har mod på at lege lidt med deres Sony D8 kamera så er de velkomne til at spørge for nu kører det bare. Mange tak for hjælpen.

Hvis henninga og hashkagen lige ville lægge et svar kan i få en skovl points.

Ole

Fint det virkede for dig !