Jeg har fået sindsygt mange Warnings og Errors på min Domain Controller efter jeg har installeret SP1 på den.
1.
Source: DNS Category: None Type: Error EventID: 4000
The DNS server was unable to open Active Directory. This DNS server is configured to obtain and use information from the directory for this zone and is unable to load the zone without it. Check that the Active Directory is functioning properly and reload the zone. The event data is the error code.
I dette særtema om aspekter af AI ser vi på skiftet fra sprogmodeller til AI-agenter, og hvordan virksomheder kan navigere i spændet mellem teknologisk hastighed og behovet for menneskelig kontrol.
Ved ikke om det er mig, er det nok, eller om det er SCW der har overset noget, men jeg har rettet i sikkerhedkonfigurationen og nu har jeg ikke den samme Error i dns'en.
Nu har jeg denne her
DNS server has updated its own host (A) records. In order to ensure that its DS-integrated peer DNS servers are able to replicate with this server, an attempt was made to update them with the new records through dynamic update. An error was encountered during this update, the record data is the error code.
If this DNS server does not have any DS-integrated peers, then this error should be ignored.
If this DNS server's Active Directory replication partners do not have the correct IP address(es) for this server, they will be unable to replicate with it.
To ensure proper replication: 1) Find this server's Active Directory replication partners that run the DNS server. 2) Open DnsManager and connect in turn to each of the replication partners. 3) On each server, check the host (A record) registration for THIS server. 4) Delete any A records that do NOT correspond to IP addresses of this server. 5) If there are no A records for this server, add at least one A record corresponding to an address on this server, that the replication partner can contact. (In other words, if there multiple IP addresses for this DNS server, add at least one that is on the same network as the Active Directory DNS server you are updating.) 6) Note, that is not necessary to update EVERY replication partner. It is only necessary that the records are fixed up on enough replication partners so that every server that replicates with this server will receive (through replication) the new data.
og så vidt jeg huske skal jeg ikke gøre noget ved den når jeg nu nok har en DC, er det ikke rigtigt?
jacla WINS benyttes stort set ikke længere, pga den er meget båndbredde krævende, maskinen skal nok få en IP i 169.x.x.x ranget tildelt selv uden wins ;) (og det er ikke for at lave ballade, men mht WINS har du altså ikke ret :D )
WINS benyttes meget sjældent nu om dage, og er IKKE installeret pr default, (og der skal heller ikke tages højde for WINS), det er DNS der er rygraden i windows systemer nu.
jo, men det nytter bare ikke noget, for WINS har en meget lille ubetydelig rolle i windows 200X og virker DNS ikke, vil ens AD også brække sig (som vi ser netop i dette spørgsmål), da DNS og AD hænger mere sammen end ærtehalm gør.
The File Replication Service is unable to add this computer to the following replica set: "DOMAIN SYSTEM VOLUME (SYSVOL SHARE)"
This could be caused by a number of problems such as: -- an invalid root path, -- a missing directory, -- a missing disk volume, -- a file system on the volume that does not support NTFS 5.0
The information below may help to resolve the problem: Computer DNS name is "hilsoedc1.hilsoe.local" Replica set member name is "HILSOEDC1" Replica set root path is "c:\windows\sysvol\domain" Replica staging directory path is "c:\windows\sysvol\staging\domain" Replica working directory path is "c:\windows\ntfrs\jet" Windows error status code is FRS error status code is FrsErrorMismatchedJournalId
Other event log messages may also help determine the problem. Correct the problem and the service will attempt to restart replication automatically at a later time.
The File Replication Service is in an error state. Files will not replicate to or from one or all of the replica sets on this computer until the following recovery steps are performed:
Recovery Steps:
[1] The error state may clear itself if you stop and restart the FRS service. This can be done by performing the following in a command window:
net stop ntfrs net start ntfrs
If this fails to clear up the problem then proceed as follows.
[2] For Active Directory Domain Controllers that DO NOT host any DFS alternates or other replica sets with replication enabled:
If there is at least one other Domain Controller in this domain then restore the "system state" of this DC from backup (using ntbackup or other backup-restore utility) and make it non-authoritative.
If there are NO other Domain Controllers in this domain then restore the "system state" of this DC from backup (using ntbackup or other backup-restore utility) and choose the Advanced option which marks the sysvols as primary.
If there are other Domain Controllers in this domain but ALL of them have this event log message then restore one of them as primary (data files from primary will replicate everywhere) and the others as non-authoritative.
[3] For Active Directory Domain Controllers that host DFS alternates or other replica sets with replication enabled:
(3-a) If the Dfs alternates on this DC do not have any other replication partners then copy the data under that Dfs share to a safe location. (3-b) If this server is the only Active Directory Domain Controller for this domain then, before going to (3-c), make sure this server does not have any inbound or outbound connections to other servers that were formerly Domain Controllers for this domain but are now off the net (and will never be coming back online) or have been fresh installed without being demoted. To delete connections use the Sites and Services snapin and look for Sites->NAME_OF_SITE->Servers->NAME_OF_SERVER->NTDS Settings->CONNECTIONS. (3-c) Restore the "system state" of this DC from backup (using ntbackup or other backup-restore utility) and make it non-authoritative. (3-d) Copy the data from step (3-a) above to the original location after the sysvol share is published.
[4] For other Windows servers:
(4-a) If any of the DFS alternates or other replica sets hosted by this server do not have any other replication partners then copy the data under its share or replica tree root to a safe location. (4-b) net stop ntfrs (4-c) rd /s /q c:\windows\ntfrs\jet (4-d) net start ntfrs (4-e) Copy the data from step (4-a) above to the original location after the service has initialized (5 minutes is a safe waiting time).
Note: If this error message is in the eventlog of all the members of a particular replica set then perform steps (4-a) and (4-e) above on only one of the members.
Tilladte BB-code-tags: [b]fed[/b] [i]kursiv[/i] [u]understreget[/u] Web- og emailadresser omdannes automatisk til links. Der sættes "nofollow" på alle links.
