Husk Password

Det skyldes at du ikke har installeret \"Klient program til Microsoft netværk\" under kontrolpanel. For at gøre det, skal du finde din Windows CD-rom frem, og gøre følgende: åbn kontrolpanel, vælg \"netværk\", klik på \"tilføj\", vælg \"klient\", vælg \"Microsoft\", og vælg \"Klient program til Microsoft Netværk\" i den højre kolonne. Bemærk! Sørg for at gemme din adgangskode, hvis programmet skulle svigte.

Hej Eksperter.

Fandt løsningen inden på MS-KB...
Så tak for forsøget

Hvad var så løsningen når det ikke var den sædvanlige som jeg har foreslået?

RESOLUTION

Windows 2000
Verify that the Network settings of the Dial-up Networking connectoid are correct:
Right-click the Dial-up Networking connectiod, and then click Properties.


Click the Network tab, and then confirm that Client for Microsoft Networks is installed and that it is selected.


Windows 95 and Windows 98
Rename your .pwl file.

NOTE: If you are using a personal certificate, export it before you rename your .pwl file. If you do not, the personal certificate may be unavailable when you send mail. For additional information, click the article number below to view the article in the Microsoft Knowledge Base:
Q190296 OLEXP: Unable to use Personal Certificates in Outlook Express
To rename your .pwl file, type the following line at a command prompt, and then press the ENTER key (where Windows is the name of the Windows folder and user_name is the user name that you use to log on to Windows):
ren c:\\Windows\\user_name.pwluser_name.xxx
After you rename your .pwl file, restart your computer.

When the Enter Network Password or Welcome To Windows dialog box is displayed, type the password that you normally use, and then click OK. When you are prompted to confirm the password that you entered, type the password again in the Confirm New Password box, and then click OK.

NOTE: If there are no .pwl files present on the drive (for example, if you press the ESC key when you are prompted for a password when Windows starts) password caching is not enabled. You must first log on to the network to create a .pwl file.


Rename the Rna.pwl file in the Windows folder; to do so, type the following line at a command prompt, and then press the ENTER key (where Windows is the name of the Windows folder):
ren c:\\Windows\\rna.pwl rna.xxx
After you rename the Rna.pwl file, restart your computer.

NOTE: The Rna.pwl file may not exist on your computer. This file is not required in some configurations.


Verify that password caching is enabled; to do so, you need to use Registry Editor.

WARNING: Using Registry Editor incorrectly can cause serious problems that may require you to reinstall your operating system. Microsoft cannot guarantee that problems resulting from the incorrect use of Registry Editor can be solved. Use Registry Editor at your own risk.

For information about how to edit the registry, view the \"Changing Keys and Values\" Help topic in Registry Editor (Regedit.exe) or the \"Add and Delete Information in the Registry\" and \"Edit Registry Data\" Help topics in Regedt32.exe. Note that you should back up the registry before you edit it. If you are running Windows NT or Windows 2000, you should also update your Emergency Repair Disk (ERD).

View the DisablePwdCaching value (a DWORD value) in the following registry key:
HKEY_LOCAL_MACHINE\\Software\\Microsoft\\Windows\\CurrentVersion\\Policies\\Network
If password caching is disabled, the DisablePwdCaching value has a value data of 1. To enable password caching, change the value data to 0.

NOTE: If the DisablePwdCaching value does not exist, add this DWORD value with a data value of 0 to the preceding registry key. You may need to remove this value altogether and then restart your computer to make caching work.


Disable automatic logon. To do so, delete the AutoLogon value (a binary value) from the following registry key:


HKEY_LOCAL_MACHINE\\Software\\Microsoft\\Windows\\CurrentVersion\\Network\\Real Mode Net
Remove Dial-Up Networking, and then reinstall it:


In the Network properties, record each Network component and its configuration information:


Click Start, point to Settings, click Control Panel, and then double-click Network.


Click a component on the Configuration tab, click Properties, and then record all of the component\'s settings. Repeat this process with another component until you record all of the component configuration information.


Click Start, point to Settings, click Control Panel, and then double-click Add/Remove Programs.


Click the Windows Setup tab.


Click Communications, and then click Details.


Click to clear the Dial-Up Networking check box, click OK, and then restart your computer if you are prompted to do so.


Repeat steps a through c.


Click to select the Dial-Up Networking check box, and then click OK.

NOTE: You may receive version conflict error messages during this process. If this occurs, click No when you are prompted to keep a newer version of each file.


If you are using the Microsoft Network (MSN) version 2.51, reinstall the MSN program.

For additional information about how to install MSN, click the article number below to view the article in the Microsoft Knowledge Base:
Q179604 How to Manually Install MSN Components from the MSN 2.51 CD-ROM
Even though user profiles are disabled, remove the ProfilesList key from the registry.

For additional information about how to remove this key from the registry, click the article number below to view the article in the Microsoft Knowledge Base:
Q156826 How to Disable and Delete User Profiles
If you are running Windows 95, you may need to add Transmission Control Protocol/Internet Protocol (TCP/IP) to the Network properties:
Click Start, point to Settings, click Control Panel, and then double-click Network.


Click Protocol, click Add, click Microsoft in the Manufacturers box, click TCP/IP, and then click OK.

Tak for det :-)

Lukker du ikke spørgsmålet så? :o)

Lukker spørgsmålet